How to Check Liner Bond Integrity After Curing

Installation & Usage 6 min read · focus: liner bond inspection tap test

Why check the bond before you scrape

Once a liner is scraped and the machine is assembled, an unbonded area is hidden under a finished surface. You will only find it later, as a low spot that keeps returning, a corner that lifts, or a bond line that starts to peel after a few months of running.

The check takes minutes and happens at the only point where repair is still cheap: after full cure, before any material is removed. If the sheet is still loose, you can cut back to sound material and re-bond. After scraping, the same defect usually means a new piece and a new fitting job.

Step one: a visual pass along every edge

Walk the full perimeter with a light held at a low angle to the surface. What you are looking for is a line that is not tight: a shadow, a slight lift, or a change in the adhesive fillet where the sheet meets the casting.

Check the ends first. Terminations see the most peeling load and are where handling damage shows up. Then run your eye along both long edges, then around any internal cut-out such as an oil groove or a bolt clearance.

Also look at the adhesive that squeezed out during clamping. A fully cured squeeze-out bead that is hard and glassy along the whole edge is a good sign. Soft, gummy or missing squeeze-out in one zone tells you where to concentrate the tapping.

Step two: tap testing

Tap the sheet with a small light hammer, a brass drift or even a coin, working in a grid. A bonded area gives a short, high, dead sound. An unbonded area rings or sounds hollow and the difference is usually obvious once you have one known-good reference point.

Keep the tapping light. The purpose is to excite the sheet, not to dent it. On thin sheet a heavy blow will mark the surface and create exactly the kind of local damage you are trying to detect.

Mark every suspicious spot with a pencil as you go, then re-tap those spots from a different angle. A genuinely unbonded patch responds the same way from any direction; a false positive from a rib or a casting web underneath often does not.

Tap testing finds plan-view voids well. It is much weaker at finding a void that sits under the middle of a wide sheet with no free edge nearby, because the sheet is still supported around it.

Step three: probe the edges

A thin feeler gauge or a sharp blade tip applied gently at the bond line shows whether the edge is truly attached. Work along the perimeter, not into the sheet. If the gauge slides in more than a token amount at one location, that edge is not bonded there.

This is the check that catches the most common real failure: an edge that looked tight but never had adhesive behind it because the bond line was starved during clamping, or because the sheet was lifted slightly while repositioning.

Reading the result: what each finding means

A small void within a few millimetres of an edge is a repair item. Cut back to sound bond, clean, re-apply adhesive and clamp. It is worth doing before scraping because the repair sits below the finished surface.

A void in the middle of a wide sheet with sound bond all around is a judgement call. If it is small and surrounded by good bond, it usually carries load through the surrounding area. If it is large, or if several voids line up across the width, do not scrape it: remove the section and re-bond, because the sheet will deflect under load and the scraping you do now will not be the shape it settles into.

A void along an entire edge, or any area where the sheet lifts under light finger pressure, is a failed bond. Re-bond that section rather than trying to inject adhesive into a gap you cannot see or verify.

After a repair: re-check before moving on

Re-tap the repaired area after the adhesive has fully cured, and probe the new edge. A repair that still sounds hollow means the first attempt did not wet out, usually because the surface was not re-prepared or the clamp pressure was not maintained.

Only then move to scraping. Log the location of any repair you made, and check those same spots at the first maintenance interval. A repair that holds for the first weeks of running is normally a permanent one; a repair that starts lifting again points to a preparation or adhesive selection problem rather than a local defect.

Quick answers

Can I check the bond without tapping, just by looking?

Visual inspection catches lifted edges and starved bond lines, but it cannot see a void in the middle of a sheet. Tapping takes a few minutes and is the only practical way to find internal unbonded areas before scraping.

The sheet sounds hollow but does not move. Is it a problem?

A hollow sound with a tight, well-supported edge is usually a small internal void. It matters mainly if it is large, if several line up across the width, or if it sits where the load is highest. Small isolated voids surrounded by sound bond normally carry load through the surrounding material.

Can I inject adhesive into a hollow area instead of re-bonding?

Injection is unreliable on a bonded slideway because you cannot see how far the adhesive travelled or whether it wet the surface properly, and drill holes in the sheet create new stress points. Cutting back to sound bond and re-bonding the section gives a result you can verify by tapping afterwards.

Related guides

Need sheet, adhesive or spotting paste for your machine? Tell us the size and application —we quote within 24 hours.

Request a Quote